دتکتورهای دود در تشخیص دود یا آتش در ساختمان ها بسیار مفید هستند و پارامترهای مهم ایمنی نیز به همین ترتیب هستند. در این جلسه DIY، ما قصد داریم یک مدار آشکارساز دود بسازیم که نه تنها دود موجود در هوا را حس می کند، بلکه میزان دود موجود در هوا را بر حسب PPM (قسمت در میلیون) می خواند و نمایش می دهد. این مدار هنگامی که سطح دود از 1000 پی پی ام بالاتر می رود، Buzzer را فعال می کند، این مقدار آستانه را می توان در کد مطابق با نیاز تغییر داد. این مدار عمدتاً از سنسور دود/گاز MQ2 و آردوینو برای تشخیص و محاسبه سطح دود استفاده می کند. سنسور گاز MQ2 نسبت به LPG، الکل و متان و غیره نیز حساس است.
این ردیاب دود را می توان به راحتی بر روی تخته نان یا تخته نقطه ساخت، اما ما تصمیم گرفتیم آن را به عنوان یک آردوینو شیلد روی PCB بسازیم. ما از شبیه ساز و طراح PCB آنلاین EasyEDA برای ساخت این سپر آشکارساز دود برای آردوینو استفاده کرده ایم . ما در این مقاله کل فرآیند را توضیح داده ایم و همچنین چیدمان PCB را برای این آردوینو شیلد ارائه کرده ایم تا در صورت نیاز بتوانید این شیلد را نیز سفارش دهید.
اجزای مورد نیاز:
- آردوینو UNO
- شیلد آردوینو آشکارساز دود (خود طراحی شده)
- منبع تغذیه
اجزای ردیاب دود آردوینو شیلد:
- سنسور دود (MQ2)
- مقاومت (10K و 1K)
- زنگ
- LCD 16×2
- قابلمه 10 هزار
- رهبری
- LM358
- نوارهای برگ
-
طراحی سپر آشکارساز دود برای آردوینو:
برای طراحی Smoke Detector Shield برای آردوینو از EasyEDA استفاده کرده ایم که در آن ابتدا یک شماتیک طراحی کرده و سپس با قابلیت Auto Routing EasyEDA آن را به طرح PCB تبدیل کرده ایم.
بیشتر بخوانید: آشکارساز دود با استفاده از سنسور گاز MQ2 و آردوینو
در ادامه، متن انگلیسی این مطلب را میتوانید مشاهده نمایید:
Smoke Detectors are very useful in detecting smoke or fire in buildings, and so are the important safety parameters. In this DIY session, we are going to build a Smoke Detector Circuit which not only sense the smoke in the air but also reads and displays the level of Smoke in the Air in PPM (parts per million). This circuit triggers the Buzzer when Smoke level becomes higher than 1000 ppm, this threshold value can be changed in the Code according to the requirement. This circuit mainly uses MQ2 Smoke/Gas sensor and Arduino to detect and calculate the level of smoke. MQ2 gas sensor is also sensible to LPG, Alcohol, and Methane etc.
This Smoke Detector can be easily built on Bread Board or Dot Board but we have decided to build this as an Arduino Shield on PCB. We have used EasyEDA online PCB simulator and designer to build this Smoke Detector Shield for Arduino. We have explained the whole process in this Article and also provided PCB layout for this Arduino Shield so that you can also order this Shield if you need.
Components Required:
- Arduino UNO
- Smoke Detector Arduino Shield (Self Designed)
- Power Supply
Components for Smoke Detector Arduino Shield:
- Smoke Sensor (MQ2)
- Resistors (10K and 1K)
- Buzzer
- 16×2 LCD
- 10k POT
- LED
- LM358
- Burg strips
-
Designing Smoke Detector Shield for Arduino:
For designing Smoke Detector Shield for Arduino we have used EasyEDA, in which first we have designed a Schematic and then converted that into the PCB layout by Auto Routing feature of EasyEDA.