این یک اصلاح محصول با قابلیت پیاده سازی آسان است که برای پزشکان، آسیب شناسان، محققان یا دیگر علاقه مندان به میکروسکوپ که علاقه مند به گرفتن تصاویر کل اسلاید یا ایجاد اسلایدهای مجازی برای استفاده بعدی هستند، بسیار مفید خواهد بود.
این دستگاه به افراد اجازه میدهد تا چندین عکس از اسلاید با بزرگنمایی بالا بگیرند، که بعداً میتوان آنها را روی یک کامپیوتر محلی یا راه دور به هم متصل کرد و مسیر را برای تجزیه و تحلیل دقیقتر تصویر هموار کرد.
![میکروسکوپ دیجیتال ارزان قیمت با حرکت اسلاید خودکار با استفاده از آردوینو](https://duino4projects.com/wp-content/uploads/2014/11/Low-cost-digital-microscope-with-automated-slide-movement-using-arduino.jpg)
مرحله 1: آنچه شما نیاز دارید
میکروسکوپ دیجیتال از قطعاتی که به راحتی در دسترس هستند استفاده می کند و با کمتر از 100 دلار می توان آنها را کنار هم قرار داد.
• مجموعه لنز برای میکروسکوپ - می توان آن را به تازگی خریداری کرد یا می توان آن را از یک میکروسکوپ قدیمی دانش آموزی نجات داد. ما تصمیم گرفتیم یک میکروسکوپ دانشجویی ارزان قیمت (50 دلار) بخریم و از مجموعه لنز برای پروژه خود استفاده کنیم.
یک چشمی 15X و لنز شیئی 45X برای پروژه ما استفاده شد.
شما همچنین به یک آینه یک طرفه 3.5 در 3.5 سانتی متری برای تغذیه داخل پریسکوپ نیاز دارید (طبق طرح پریسکوپ پرینت سه بعدی).
• موتورهای پله ای مینیاتوری (2 شماره) از درایوهای CD-ROM قدیمی – این موتورها را می توان به راحتی از فروشگاه های دست دوم با قیمت کمتر از 10 دلار تهیه کرد.
همچنین می توان اینها را به همراه کالسکه استیج و متحرک خریداری کرد - http://www.aliexpress.com/item/New4-5V-2-phase-4-wire-stepper-motor-with-screw-drive-slider-slider-slider -for-DIY-miniature/1139615226.html
از موتورهای پله ای برای حرکت اسلاید به صورت شبکه ای استفاده می شود.
• بدنه میکروسکوپ – گزینه های متعددی برای این کار موجود است
o نگه داشتن پایه میکروسکوپ از میکروسکوپ دانش آموز و استفاده از آن برای قرار دادن مکانیسم حرکت اسلاید
o یک مدل سه بعدی خوب نیز در http://www.thingiverse.com/thing یافت می شود. :92355
o ما طراحی خود را به بهترین وجه مطابق با نیازهایمان ایجاد کردیم. طراحی اصلاح شده فضای اضافی زیر پایه اسلاید را حذف می کند و طراحی را فشرده تر و ارگونومیک تر می کند. این طراحی همچنین دارای یک چیدمان نصب برای مجموعه موتور است و امکان حرکت بدون مانع نگهدارنده اسلاید را فراهم می کند.
• وب کم برای گرفتن تصاویر اسلاید جداگانه.
• دوخت تصاویر گرفته شده با استفاده از فیجی، یک ابزار دوخت تصویر منبع باز – http://fiji.sc/Image_Stitching
• LED 0.5W – زیر اسلاید قرار می گیرد و برای روشن کردن تصویر زیر میکروسکوپ استفاده می شود.
برای جزئیات بیشتر: میکروسکوپ دیجیتال ارزان قیمت با حرکت اسلاید خودکار با استفاده از آردوینو
در ادامه، متن انگلیسی این مطلب را میتوانید مشاهده نمایید:
The device allows one to take multiple images of the slide under high magnification, which can later be stitched together on a local or remote computer, paving the road for more accurate image analysis.
![Low cost digital microscope with automated slide movement using arduino](https://duino4projects.com/wp-content/uploads/2014/11/Low-cost-digital-microscope-with-automated-slide-movement-using-arduino.jpg)
Step 1: What you will need
The digital microscope uses readily available parts and can be put together in less than $100.
• Lens assembly for the microscope – This can be newly purchased or can be salvaged from an old student microscope. We decided to buy a low cost student microscope ($50) and use the lens assembly for our project.
A 15X eyepiece and 45X objective lens were used for our project.
You will also need a 3.5 cm x 3.5 cm one way mirror to feed inside the periscope (as per 3D printed periscope design).
• Miniature stepper motors (2 nos.) from old CD-ROM drives – These can be easily sourced from second hand stores for less than $10.
One could also buy these along with a stage and movable carriage – http://www.aliexpress.com/item/New4-5V-2-phase-4-wire-stepper-motor-with-screw-drive-slider-slider-for-DIY-miniature/1139615226.html
The stepper motors are used to move the slide in a grid-wise manner.
• Microscope body – There are multiple options available for this
o Retain the microscope stand from the student microscope and use it to house the slide movement mechanism
o A good 3D model can also be found at http://www.thingiverse.com/thing:92355
o We created our own design to best suit our needs. The modified design eliminates the additional space under the slide base, making the design more compact and ergonomic. The design also incorporates a mounting arrangement for the motor assembly and allows for unobstructed movement of the slide holder.
• Webcam to capture individual slide images.
• Stitching of the captured images is carried out using Fiji, an open-source image stitching tool – http://fiji.sc/Image_Stitching
• 0.5W LED – This is placed under the slide and is used for illuminating the image under the microscope
For more detail: Low cost digital microscope with automated slide movement using arduino