![](https://duino4projects.com/wp-content/uploads/2019/09/How-to-Make-the-Knock-Lock-for-Arduino-Starter-Kit.jpg)
در این آموزش من ویدیویی را به شما نشان خواهم داد که چگونه با استفاده از کیت استارتر arduino uno یک قفل ضربه ای درست کردم. من در طول راه با چند مشکل مواجه شدم اما پس از فکر کردن به راه حلی رسیدم. این اولین پروژه آردوینو است که من ساخته ام، بنابراین من صرفاً از دستورالعمل های کتابچه ارائه شده در کیت خارج شدم. ممکن است هنگام انتخاب قفل ضربه ای بدون تجربه قبلی کمی جلوتر رفته باشم، اما آن را کامل کردم و بیشتر مطابق با مشخصات دفترچه راهنما هستم، امیدوارم از این آموزش لذت ببرید و از هر گونه راهنمایی و پیشنهادی که ارائه دهید قدردانی می کنم.
مرحله 1: Knock Lock در عمل
![](https://duino4projects.com/wp-content/uploads/2019/09/The-Knock-Lock-in-Action.jpg)
اینجا را کلیک کنید تا ویدیوی من را در مورد نمای کلی پروژه ام ببینید (با عرض پوزش بابت صدایم که هنگام ساخت این فیلم بیمار بودم). من مجبور شدم پیزو را دوباره سیم کشی کنم زیرا نه تنها دکمه تنظیم مجدد را پاک نمی کرد، شاخک های پایین نیز همانطور که در کتاب نشان داده شده است فاصله نداشتند، بنابراین مجبور شدم از سیم های جامپر برای سیم کشی صحیح آن استفاده کنم و سپس آن را به پیزو سیم کشی کنم.
منبع: نحوه ساخت Knock Lock برای کیت استارت آردوینو
در ادامه، متن انگلیسی این مطلب را میتوانید مشاهده نمایید:
![](https://duino4projects.com/wp-content/uploads/2019/09/How-to-Make-the-Knock-Lock-for-Arduino-Starter-Kit.jpg)
In this instructable i will be showing you a video on how I made a knock lock using the arduino uno starter kit. I did run into a few problems along the way but figured out a solution after thinking it over. this is the first arduino project I have made so i went solely off of the directions in the booklet provided in the kit. I may have gotten a bit ahead of myself when choosing to do the knock lock with no prior experience but i completed it and mostly to the manuals specification I hope you enjoy this instructable and I would appreciate any tips and suggestions that you have to offer.
Step 1: The Knock Lock in Action
![](https://duino4projects.com/wp-content/uploads/2019/09/The-Knock-Lock-in-Action.jpg)
click here to see my video on my overview of my project (sorry about my voice i was sick when making this). I had to rewire the piezo because not only was it not clearing the reset button the prongs on the bottom were not spaced as showed in the book so I had to use jumper wires to properly wire it then wire it to the piezo.